Resources

How to Install Pipe Markers

Step-by-step installation for every Craftmark marker, plus where ASME A13.1 says they go. Most jobs need a tape measure and a rag, nothing more.

Before you start

Measure the outside diameter

Measure the outside of the pipe. On insulated pipe, measure over the insulation, since the marker goes on the jacket. No tape handy? Wrap a string around the pipe and divide its length by 3.14.

Check size, legend and color

Each marker size fits a range of pipe OD. Confirm the legend matches the contents and the color matches ASME A13.1-2023 or your spec.

Know the flow direction

Every marker needs an arrow pointing the way the contents flow. Where flow runs both ways, use a double-ended arrow.

Self-stick markers need clean, dry pipe

DuraMark, RollMark and arrow tape go on clean, dry surfaces at 50°F or warmer. Wipe off dust and oil first.

Snap-on markers need no prep

SpecMark goes on wet, oily, cold, dirty or rusty pipe and insulation as-is.

Service temperature

Our markers are rated from -40°F to 180°F on the pipe surface. Hotter than that? Call us before you order.

SpecMark™ Snap-On (sizes AA–E)

Pre-coiled and pre-tensioned plastic that snaps around the pipe. No adhesive on the pipe, no surface prep, 360° visibility.

  1. Check the arrow.Hold the marker so the printed arrows point with the flow and the legend reads right side up from where people will see it.
  2. Open the coil.Pull the edges apart just enough to fit over the pipe.
  3. Snap it on.Place it on the pipe and let go. It springs closed and grips on its own.
  4. Sizes D and E: lock the overlap.Peel the liner off the adhesive strip and press the overlap down so the marker holds to itself.
  5. Slide it into place.Move it along the pipe to the spot you want. It can be removed and reused later.
Works on wet, oily, cold, dirty or rusty pipe and on insulation. Great for retrofits where you can't clean the pipe.

SpecMark™ G* and H* (strap-on)

For pipe 6.8" OD and up. These ship flat and hold on with UV-stabilized black nylon straps: 2 for G*, 3 for H*. They aren't 360°, so place them where they'll be seen.

  1. Pick the viewing side.Place the marker on the side of the pipe people see from the aisle or floor.
  2. Position the markerwith the arrow pointing with the flow.
  3. Strap it.Wrap a strap around the pipe over each end of the marker (and the middle, on H*), then pull it snug.
  4. Trim the tailsof the straps.

DuraMark™ Self-Stick

Durable vinyl with an aggressive acrylic adhesive. A low-cost marker for clean, dry pipe and insulation jackets.

  1. Clean and dry the spot.Wipe off dust, oil and moisture. Isopropyl alcohol works well on metal pipe.
  2. Check the temperature.Apply at 50°F or warmer so the adhesive grabs.
  3. Peel and place.Peel the backing, line the legend up where it will be seen, and press it on from the center out to push out air.
  4. Rub it down firmlyacross the whole marker, especially the edges.
  5. Seal the ends with arrow tape.Wrap a band of matching arrow tape around the pipe at each end, overlapping the marker edge, with the arrows pointing with the flow.
The arrow tape bands do two jobs: they lock the marker ends down and show flow direction all the way around the pipe.

RollMark™ IV Self-Stick Rollform

A 30 ft continuous roll with the legend repeating so it reads 360° around the pipe. Cut off what each marker needs. Great for long runs of the same legend.

  1. Clean and dry the spot,50°F or warmer.
  2. Measure the wrap.Pipe OD × 3.14 is the distance around the pipe. Add about 1" for overlap.
  3. Cut the piecefrom the roll with a utility knife or scissors.
  4. Peel and wrapit around the pipe, pressing it down as you go, and finish with the overlap on the side away from view.
  5. Add flow arrowswith a band of arrow tape next to it.

RollMark™ V Self-Stick Rollform

Each roll has 50 legends and 50 detachable arrows, so every marker comes with its own arrow panel.

  1. Clean and dry the spot,50°F or warmer.
  2. Peel a legendoff the roll and press it onto the pipe where it will be seen.
  3. Detach the arrowpanel along the cut line.
  4. Place the arrownext to the legend, pointing with the flow, and rub both down firmly.

Arrow & banding tape

90 ft rolls in every ASME color. Use it to seal the ends of self-stick markers and to show flow direction.

  1. Match the marker.Use the same color scheme and the tape width for your marker size.
  2. Clean and dry the pipe,50°F or warmer.
  3. Wrap one bandaround the pipe with the arrows pointing with the flow, so the ends meet or just overlap.
  4. Press it downall the way around.
One 90 ft roll makes about 344 bands on 1" OD pipe, 172 on 2" OD, 86 on 4" OD and 57 on 6" OD. The calculator figures rolls for you.

Where markers go (ASME A13.1-2023)

Markers go wherever someone needs to know what's in the pipe. The standard calls for them at these points:

Next to valves and flanges

So anyone working the valve knows what it controls.

At every change of direction

At elbows, bends and where the run turns.

At branches

On the branch line at each tee.

Both sides of walls and floors

Wherever the pipe passes through, mark it on each side.

Along straight runs

At regular intervals so a marker is always in view. Every 25 to 50 ft is typical; your spec may say otherwise.

Where people can see them

If the pipe is above eye level, put the marker below the centerline; if it's below, put it above.

Common questions

Can markers go on insulated pipe?

Yes. Measure the outside diameter over the insulation and size the marker to that. Self-stick markers need a clean, dry jacket.

Which way does the arrow point?

In the direction the contents flow. If flow goes both ways, use arrows at both ends or a double-ended arrow.

It's too cold to use self-stick markers. What now?

Self-stick markers and tape need 50°F or warmer to apply. SpecMark snap-on markers put no adhesive on the pipe, so cold pipe isn't a problem.

How long do they last outdoors?

About 5 years for DuraMark and 5 to 8 years for SpecMark, depending on sun, weather and color.

Can I move a marker later?

SpecMark can be removed and reused. Self-stick markers are meant to stay put.

Questions on a job?

Call us and talk to someone who has marked a lot of pipe.